Profile image of Ian Gibson

Prof Ian Gibson

STAFF PROFILE

Position

Professor

Faculty

Faculty of Sci Eng & Built Env

Department

School of Engineering

Campus

Geelong Waurn Ponds Campus

Contact

ian.gibson@deakin.edu.au
+61 3 522 73094

Publications

Filter by

2020

Modelling of laser powder bed fusion process and analysing the effective parameters on surface characteristics of Ti-6Al-4V

A Khorasani, I Gibson, A Ghasemi, A Ghaderi

(2020), Vol. 168, pp. 1-14, International Journal of Mechanical Sciences, Amsterdam, The Netherlands, C1

journal

Two and three-dimensional characterisation of localised corrosion affected by lack-of-fusion pores in 316L stainless steel produced by selective laser melting

M Laleh, A Hughes, S Yang, J Li, W Xu, I Gibson, M Tan

(2020), Vol. 165, pp. 1-12, Corrosion Science, Amsterdam, The Netherlands, C1

journal

A review of laser engineered net shaping (LENS) build and process parameters of metallic parts

M Izadi, A Farzaneh, M Mohammed, I Gibson, B Rolfe

(2020), pp. 1-20, Rapid Prototyping Journal, Bradford, Eng., C1

journal
2019

The effect of SLM process parameters on density, hardness, tensile strength and surface quality of Ti-6Al-4V

A Khorasani, I Gibson, U Awan, A Ghaderi

(2019), Vol. 25, pp. 176-186, Additive manufacturing, Amsterdam, The Netherlands, C1

journal

Oscillation characteristics of low Weber number impinging micro-droplets

S Das, M Mohammed, I Gibson, L Weerasiri, A McDonnell, J Xiang, L Yeo

(2019), Vol. 33, pp. 197-213, Theoretical and computational fluid dynamics, Berlin, Germany, C1

journal

Investigation on the effect of heat treatment and process parameters on the tensile behaviour of SLM Ti-6Al-4V parts

A Khorasani, I Gibson, A Ghaderi, M Mohammed

(2019), Vol. 101, pp. 3183-3197, International journal of advanced manufacturing technology, London, Eng., C1

journal

Unexpected erosion-corrosion behaviour of 316L stainless steel produced by selective laser melting

M Laleh, A Hughes, W Xu, I Gibson, M Tan

(2019), Vol. 155, pp. 67-74, Corrosion science, Amsterdam, The Netherlands, C1

journal

A comprehensive study on variability of relative density in selective laser melting of Ti-6Al-4V

A Khorasani, I Gibson, A Ghasemi, A Ghaderi

(2019), Vol. 14, pp. 349-359, Virtual and physical prototyping, Abingdon, Eng., C1

journal

On the unusual intergranular corrosion resistance of 316L stainless steel additively manufactured by selective laser melting

M Laleh, A Hughes, W Xu, N Haghdadi, K Wang, P Cizek, I Gibson, M Tan

(2019), Vol. 161, pp. 1-7, Corrosion science, Amsterdam, The Netherlands, C1

journal

Directed energy deposition and characterization of high-carbon high speed steels

N Ur Rahman, L Capuano, S Cabeza, M Feinaeugle, A Garcia-Junceda, M de Rooij, D Matthews, G Walmag, I Gibson, G Rmer

(2019), Vol. 30, pp. 1-11, Additive Manufacturing, Amsterdam, The Netherlands, C1

journal

Corrosion behaviour of additively manufactured type 316L stainless steel

Majid Laleh, Anthony Hughes, Wei Xu, Ian Gibson, Yongjun Tan

(2019), pp. 1-9, Proceedings of the 2019 Australasian Conference on Corrosion & Prevention, Melbourne, Vic., E1

conference
2018

A comprehensive study on surface quality in 5-axis milling of SLM Ti-6Al-4V spherical components

A Khorasani, I Gibson, M Goldberg, G Littlefair

(2018), Vol. 94, pp. 3765-3784, International journal of advanced manufacturing technology, London, Eng., C1

journal

Investigation on the effect of a pre-center drill hole and tool material on thrust force, surface roughness, and cylindricity in the drilling of Al7075.

A Ghasemi, A Khorasani, I Gibson

(2018), Vol. 11, Materials, Basel, Switzerland, C1

journal

Fabrication of polycaprolactone-silanated ?-tricalcium phosphate-heparan sulfate scaffolds for spinal fusion applications

G Bhakta, A Ekaputra, B Rai, S Abbah, T Tan, B Le, A Chatterjea, T Hu, T Lin, M Arafat, A van Wijnen, J Goh, V Nurcombe, K Bhakoo, W Birch, L Xu, I Gibson, H Wong, S Cool

(2018), Vol. 18, pp. 818-830, Spine journal, Amsterdam, The Netherlands, C1-1

journal

Mass transfer and flow in additive manufacturing of a spherical component

A Khorasani, I Gibson, M Asadnia, W O Neill

(2018), Vol. 96, pp. 3711-3718, International Journal of Advanced Manufacturing Technology, London, Eng., C1

journal

Augmented patient-specific facial prosthesis production using medical imaging modelling and 3D printing technologies for improved patient outcomes

M Mohammed, B Cadd, G Peart, I Gibson

(2018), Vol. 13, pp. 164-176, Virtual and physical prototyping, Abingdon, Eng., C1

journal

Characterizing the effect of cutting condition, tool path, and heat treatment on cutting forces of selective laser melting spherical component in five-axis milling

A Khorasani, I Gibson, M Goldberg, G Littlefair

(2018), Vol. 140, pp. 1-16, Journal of manufacturing science and engineering, New York, N.Y., C1

journal

Motion segmentation of the greenside bunker shot for training and coaching purposes

J Wivou, P Pathirana, I Gibson, L Udawatta

(2018), pp. 1-6, ICECTA 2017 : Proceedings of the International Conference on Electrical and Computing Technologies and Applications, Ras Al Khaimah, United Arab Emirates, E1

conference

Rheological characterization of process parameters influence on surface quality of Ti-6Al-4V parts manufactured by selective laser melting

A Khorasani, I Gibson, A Ghaderi

(2018), Vol. 97, pp. 3761-3775, International journal of advanced manufacturing technology, London, Eng., C1

journal

Design of three-dimensional, triply periodic unit cell scaffold structures for additive manufacturing

Mazher Mohammed, Ian Gibson

(2018), Vol. 140, pp. 1-10, Journal of mechanical design, New York, N.Y., C1

journal

Accelerating experimental design by incorporating experimenter hunches

C Li, R Santu, S Gupta, V Nguyen, S Venkatesh, A Sutti, D De Celis Leal, T Slezak, M Height, M Mohammed, I Gibson

(2018), Vol. 2018-November, pp. 257-266, IEEE ICDM 2018 : International Conference on Data Mining, Singapore, E1

conference
2017

Finding line of action of the force exerted on erect spine based on lateral bending test in personalization of scoliotic spine models

A Jalalian, F Tay, S Arastehfar, I Gibson, G Liu

(2017), Vol. 55, pp. 673-684, Medical & biological engineering & computing, Berlin, Germany, C1

journal

Fabrication of microfluidic devices: improvement of surface quality of CO2 laser machined poly(methylmethacrylate) polymer

M Mohammed, A Kouzani, I Gibson, M Zainal Alam

(2017), Vol. 27, pp. 1-12, Journal of micromechanics and microengineering, Bristol, Eng., C1

journal

Improving EDM Process on AZ31 Magnesium Alloy towards Sustainable Biodegradable Implant Manufacturing

A Abdul-Rani, M Razak, G Littlefair, I Gibson, A Nanimina

(2017), pp. 504-509, Proceedings of the first International Conference on Sustainable Materials Processing and Manufacturing, Skukuza, South Africa, E1

conference

Design and fabrication considerations for three dimensional scaffold structures

M Mohammed, P Badwal, I Gibson

(2017), pp. 120-126, DesTech 2016 : Proceedings of the International Conference on Design and Technology, Geelong, Victoria, E1

conference

Advanced auricular prosthesis development by 3D modelling and multi-material printing

M Mohammed, J Tatineni, B Cadd, G Peart, I Gibson

(2017), pp. 37-43, DesTech 2016: Proceedings of the International Conference on Design and Technology, Geelong, Vic., E1

conference

Customised design of a patient specific 3D printed whole mandible implant

M Mohammed, A Fitzpatrick, I Gibson

(2017), pp. 104-111, DesTech 2016: Proceedings of the International Conference on Design and Technology, Geelong, Vic., E1

conference

A low carbon footprint approach to the reconstitution of plastics into 3D-printer filament for enhanced waste reduction

M Mohammed, M Mohan, A Das, M Johnson, P Badwal, D McLean, I Gibson

(2017), pp. 234-241, DesTech 2016: Proceedings of the International Conference on Design and Technology, Geelong, Victoria, E1

conference

Design of a patient specific, 3D printed arm cast

A Fitzpatrick, M Mohammed, P Collins, I Gibson

(2017), pp. 135-142, DesTech 2016: Proceedings of the International Conference on Design and Technology, Geelong, Victoria, E1

conference

Production of Ti-6Al-4V acetabular shell using selective laser melting: possible limitations in fabrication

A Khorasani, I Gibson, M Goldberg, G Littlefair

(2017), Vol. 23, pp. 110-121, Rapid prototyping journal, Bingley, Eng., C1

journal

The changing face of additive manufacturing

I Gibson

(2017), Vol. 28, pp. 10-17, Journal of manufacturing technology management, Bingley, Eng., C1

journal

Application of emotional design to the form redesign of a midwifery training aid

J Mao, B Horan, H Forbes, S Smilevski, T Bucknall, C Nagle, D Phillips, I Gibson

(2017), Vol. 43, pp. 44-50, DesTech 2016 : Proceedings of the International Conference of Design and Technology, Geelong, Australia, E1

conference

3D printed hydrogel soft actuators

A Zolfagharian, A Kouzani, S Khoo, I Gibson, A Kaynak

(2017), pp. 2272-2277, TENCON 2016 : Technologies for smart nation : Proceedings of the 2016 IEEE Region 10 Conference, Marina Bay Sands, Singapore, E1

conference

On the role of different annealing heat treatments on mechanical properties and microstructure of selective laser melted and conventional wrought Ti-6Al-4V

A Khorasani, I Gibson, M Goldberg, G Littlefair

(2017), Vol. 23, pp. 295-304, Rapid prototyping journal, Bingley, United Kingdom, C1

journal

3D printing of a photo-thermal self-folding actuator

A Zolfagharian, A Kouzani, B Nasri-Nasrabadi, S Adams, S Khoo, M Norton, I Gibson, A Kaynak

(2017), pp. 15-22, DesTech 2016: Proceedings of the International Conference on Design and Technology, Geelong, Victoria, E1

conference

The effect of vibration during friction stir welding on corrosion behavior, mechanical properties, and machining characteristics of stir zone

S Fouladi, A Ghasemi, M Abbasi, M Abedini, A Khorasani, I Gibson

(2017), Vol. 7, pp. 421-433, Metals, Basel, Switzerland, C1

journal

Smart chair for monitoring of sitting behavior

M Huang, I Gibson, R Yang

(2017), pp. 274-280, DesTech 2016: Proceedings of the International Conference on Design and Technology, Geelong, Victoria, E1

conference

Thermal stress flow analysis in fabrication of acetabular shells using SLM

A Khorasani, I Gibson, M Goldberg, M Movahedi, G Littlefair

(2017), pp. 297-307, DesTech 2016: Proceedings of the International Conference on Design and Technology, Geelong, Victoria, E1

conference

Transformation in engineering education - a case study of remote learning experiences in China

V Huynh, S Chandrasekaran, J Long, Y Guo, I Gibson

(2017), pp. 677-686, AAEE 2017 : Integrated engineering : Proceedings of the 28th Australasian Association for Engineering Education Annual Conference, Sydney, N.S.W., E1

conference

EcoPrinting: investigating the use of 100% recycled acrylonitrile butadiene styrene (ABS) for additive manufacturing

M Mohammed, Anirudra Das, Eli Gomez-Kervin, Daniel Wilson, Ian Gibson

(2017), pp. 532-542, SFF 2017 : Proceedings of the 28th Annual International Solid Freeform Fabrication Symposium - An Additive Manufacturing Conference, Austin, Tex., E1

conference

Design optimisation of a thermoplastic splint

Angus Fitzpatrick, M Mohammed, Paul Collins, Ian Gibson

(2017), pp. 2409-2418, SFF 2017 : Proceedings of the 28th Annual International 2409 Solid Freeform Fabrication Symposium ? An Additive Manufacturing Conference, Austin, Tex., E1

conference
2016

Analysis of compressive load on intervertebral joint in standing and sitting postures

M Huang, K Hajizadeh, I Gibson, T Lee

(2016), Vol. 24, pp. 215-223, Technology and health care, Amsterdam, The Netherlands, C1

journal

Investigation on the effect of cutting fluid pressure on surface quality measurement in high speed thread milling of brass alloy (C3600) and aluminium alloy (5083)

A Khorasani, I Gibson, M Goldberg, E Doeven, G Littlefair

(2016), Vol. 82, pp. 55-63, Measurement: journal of the international measurement confederation, Amsterdam, The Netherlands, C1

journal

The influence of various seat design parameters: a computational analysis

M Huang, K Hajizadeh, I Gibson, T Lee

(2016), Vol. 26, pp. 356-366, Human factors and ergonomics In manufacturing, London, Eng., C1

journal

A survey on mechanisms and critical parameters on solidification of selective laser melting during fabrication of Ti-6Al-4V prosthetic acetabular cup

A Khorasani, I Gibson, M Goldberg, G Littlefair

(2016), Vol. 103, pp. 348-355, Materials and design, Amsterdam, The Netherlands, C1

journal

Design for additive manufacturing: trends, opportunities, considerations, and constraints

M Thompson, G Moroni, T Vaneker, G Fadel, R Campbell, I Gibson, A Bernard, J Schulz, P Graf, B Ahuja, F Martina

(2016), Vol. 65, pp. 737-760, CIRP annals - manufacturing technology, Amsterdam, The Netherlands, C1

journal

An improved static model for tool deflection in machining of Ti-6Al-4V acetabular shell produced by selective laser melting

A Khorasani, I Gibson, N Godarzvand Chegini, M Goldberg, A Ghasemi, G Littlefair

(2016), Vol. 92, pp. 534-544, Measurement: journal of the International Measurement Confederation, Amsterdam, The Netherlands, C1

journal

Additive manufacturing in the cycling industry: mainstream or gimmick?

P Collins, I Gibson

(2016), pp. 77-81, ICDF 2016 : Proceedings of the 2nd International Conference on Digital Fabrication, Tokyo, Japan, E1

conference

Industry case study: rapid prototype of mountain bike frame section

P Collins, R Leen, I Gibson

(2016), Vol. 11, pp. 295-303, Virtual and physical prototyping, Abingdon, Eng., C1

journal

Evolution of 3D printed soft actuators

A Zolfagharian, A Kouzani, S Khoo, A Moghadam, I Gibson, A Kaynak

(2016), Vol. 250, pp. 258-272, Sensors and actuators A: physical, Amsterdam, The Netherlands, C1

journal

Applications of 3D topography scanning and multi-material additive manufacturing for facial prosthesis

M Mohammed, J Tatineni, B Cadd, G Peart, I Gibson

(2016), pp. 1695-1707, SFF Symp 2016 : Proceedings of the 27th Annual International Solid Freeform Fabrication Symposium, Austin, Texas, E1

conference

Customised design and development of patient specific 3D printed whole mandible implant

M Mohammed, I Gibson, S Malyala, A Fitzpatrick

(2016), pp. 1708-1717, SFF Symp 2016 : Proceedings of the 27th Annual International Solid Freeform Fabrication Symposium, Austin, Texas, E1

conference

Machinability of metallic and ceramic biomaterials : a review

A Khorasani, I Gibson, M Goldberg, J Nomani, G Littlefair

(2016), Vol. 8, pp. 1491-1511, Science of advanced materials, Stevenson Ranch, Cal., C1

journal

The disruptive evolution of 3D printing

B Panda, M Tan, I Gibson, C Chua

(2016), pp. 152-157, Pro-AM 2016 : Proceedings of the 2nd International Conference on Pro-AM Progress in Additive Manufacturing, Singapore, E1

conference

A miniature closed-loop deep brain stimulation device

M Parastarfeizabadi, A Kouzani, I Gibson, S Tye

(2016), Vol. 2016-October, pp. 1786-1789, EMBC 2016 : Empowering Individual Healthcare Decisions : Proceedings of the 38th IEEE Engineering in Medicine and Biology Society Conference, Orlando, Florida, E1

conference

Biokin based system for capturing golf swing data

J Wivou, P Pathirana, I Gibson, L Udawatta

(2016), pp. 1-5, ICIAFS 2016 : Interoperable Sustainable Smart Systems for Next Generation : Proceedings of the 2016 IEEE 8th International Conference on Information and Automation for Sustainability, Galle, Sri Lanka, E1

conference

Sustainable frugal design using 3D printing

I Gibson, A Shukla

(2016), pp. 85-100, Handbook of sustainability in additive manufacturing. Volume 2, Singapore, B1

chapter
2015

Development and validation of a discretised multi-body spine model in LifeMOD for biodynamic behaviour simulation

K Huynh, I Gibson, B Jagdish, W Lu

(2015), Vol. 18, pp. 175-184, Computer methods in biomechanics and biomedical engineering, Abingdon, Eng., C1-1

journal

Lab-on-a-chip or Chip-in-a-lab: challenges of commercialization lost in translation

M Mohammed, S Haswell, I Gibson

(2015), Vol. 20, pp. 54-59, Procedia technology, Amsterdam, The Netherlands, C1

journal

Design and fabrication of a capacitance based wearable pressure sensor using e-textiles

A Arogbonlo, C Usma, A Kouzani, I Gibson

(2015), Vol. 20, pp. 270-275, Procedia technology, Amsterdam, The Netherlands, C1

journal

Fabrication of force sensor circuits on wearable conductive textiles

C Usma, A Kouzani, J Chua, A Arogbonlo, S Adams, I Gibson

(2015), Vol. 20, pp. 263-269, Procedia technology, Amsterdam, The Netherlands, C1

journal

Improved manufacturing quality and bonding of laser machined microfluidic systems

M Mohammed, K Quayle, R Alexander, E Doeven, Y Nai, S Haswell, A Kouzani, I Gibson

(2015), Vol. 20, pp. 219-224, Procedia technology, Amsterdam, The Netherlands, C1

journal

Influence of fill gap on flexural strength of parts fabricated by curved layer fused deposition modeling

H Guan, M Savalani, I Gibson, O Diegel

(2015), Vol. 20, pp. 243-248, Procedia technology, Amsterdam, The Netherlands, C1

journal

Simplifying medical additive manufacturing: making the surgeon the designer

I Gibson, A Srinath

(2015), Vol. 20, pp. 237-242, Procedia technology, Amsterdam, The Netherlands, C1

journal

Virtual lumbar spine of multi-body model based on simbody

Z Gao, I Gibson, C Ding, J Wang, J Wang

(2015), Vol. 20, pp. 26-31, Procedia technology, Amsterdam, The Netherlands, C1

journal

Micro prototyping and fabrication in manufacturing

I Gibson

(2015), pp. 2551-2566, Handbook of manufacturing engineering and technology, London, Eng., B1-1

chapter
2014

Effects of scaffold architecture on cranial bone healing

A Berner, M Woodruff, C Lam, M Arafat, S Saifzadeh, R Steck, J Ren, M Nerlich, A Ekaputra, I Gibson, D Hutmacher

(2014), Vol. 43, pp. 506-513, International Journal of Oral and Maxillofacial Surgery, C1-1

journal

State of the art and future direction of additive manufactured scaffolds-based bone tissue engineering

M Arafat, I Gibson, X Li

(2014), Vol. 20, pp. 13-26, Rapid prototyping journal, Bingley, Eng., C1-1

journal

A novel classification and online platform for planning and documentation of medical applications of additive manufacturing

J Tuomi, K-S Paloheimo, J Vehvilinen, R Bjrkstrand, M Salmi, E Huotilainen, R Kontio, S Rouse, I Gibson, A Mkitie

(2014), Vol. 21, pp. 553-559, Surgical Innovation, Thousand Oaks, Calif., C1-1

journal
2013

Developing a 3D multi-body model of a scoliotic spine during lateral bending for comparison of ribcage flexibility and lumbar joint loading to the normal model

K Hajizadeh, M Huang, I Gibson, G Liu

(2013), Vol. 3 A, ASME International Mechanical Engineering Congress and Exposition, Proceedings (IMECE), E1-1

conference

Teaching of the design of rehabilitation technology to engineering students

N Iris, A Putra, I Gibson

(2013), i-CREATe 2013 - International Convention on Rehabilitation Engineering and Assistive Technology, in Conjunction with SENDEX 2013, E1-1

conference

Computational biomechanical modeling of scoliotic spine: Challenges and opportunities

A Jalalian, I Gibson, E Tay

(2013), Vol. 1, pp. 401-411, Spine Deformity, C1-1

journal

Process and material behavior modeling for a new design of micro-additive fused deposition

M Monzn, I Gibson, A Bentez, L Lorenzo, P Hernndez, M Marrero

(2013), Vol. 67, pp. 2717-2726, International Journal of Advanced Manufacturing Technology, C1-1

journal
2012

Development of a human spine simulation system

I Gibson, B Jagdish, K Hajizedah, H Tho, H Mengjie, C Dissanayake

(2012), pp. 1-1, Advances in therapeutic engineering, Abingdon, England, B1-1

chapter

Development of a virtual musculo-skeletal, multi-body scoliotic spine model

K Hajizadeh, G Liu, I Gibson, M Huang

(2012), i-CREATe 2012 - 6th International Convention on Rehabilitation Engineering and Assistive Technology, E1-1

conference

Effect of sitting posture on spine joint angles and forces

M Huang, T Lee, I Gibson, K Hajizadeh

(2012), i-CREATe 2012 - 6th International Convention on Rehabilitation Engineering and Assistive Technology, E1-1

conference

Ask not what additive manufacturing can do for you

I Gibson

(2012), pp. 93-97, 23rd Annual International Solid Freeform Fabrication Symposium - An Additive Manufacturing Conference, SFF 2012, E1-1

conference
2011

History of Stereolithographic Processes

Paulo Bartolo, Ian Gibson

(2011), pp. 37-56, STEREOLITHOGRAPHY: MATERIALS, PROCESSES AND APPLICATIONS, B1-1

chapter

Getting rid of the wires: Curved layer fused deposition modeling in conductive polymer additive manufacturing

O Diegel, S Singamneni, B Huang, I Gibson

(2011), Vol. 467-469, pp. 662-667, Key Engineering Materials, C1-1

journal

Curved layer fused deposition modeling in conductive polymer additive manufacturing

O Diegel, S Singamneni, B Huang, I Gibson

(2011), Vol. 199-200, pp. 1984-1987, Advanced Materials Research, C1-1

journal

Biomimetic composite coating on rapid prototyped scaffolds for bone tissue engineering

M Arafat, C Lam, A Ekaputra, S Wong, X Li, I Gibson

(2011), Vol. 7, pp. 809-820, Acta Biomaterialia, C1-1

journal

High performance additive manufactured scaffolds for bone tissue engineering application

M Tarik Arafat, C Lam, A Ekaputra, S Wong, C He, D Hutmacher, X Li, I Gibson

(2011), Vol. 7, pp. 8013-8022, Soft Matter, C1-1

journal
2010

Additive manufacturing technologies: Rapid prototyping to direct digital manufacturing

I Gibson, D Rosen, B Stucker

(2010), pp. 1-459, Additive Manufacturing Technologies: Rapid Prototyping to Direct Digital Manufacturing, A1-1

book

Design rules for additive manufacture

I Gibson, G Goenka, R Narasimhan, N Bhat

(2010), pp. 705-716, 21st Annual International Solid Freeform Fabrication Symposium - An Additive Manufacturing Conference, SFF 2010, E1-1

conference

Haptically integrated simulation of a finite element model of thoracolumbar spine combining offline biomechanical response analysis of intervertebral discs

K Huynh, Z Gao, I Gibson, W Lu

(2010), Vol. 42, pp. 1151-1166, CAD Computer Aided Design, C1-1

journal

Layer manufacturing of magnesium and its alloy structures for future applications

C Ng, M Savalani, H Man, I Gibson

(2010), Vol. 5, pp. 13-19, Virtual and physical prototyping, Abingdon, England, C1-1

journal

Rapidpre: A new additive manufacturing technique based on reaction injection moulding

I Gibson, A Mateus, P Bartolo

(2010), pp. 1589-1590, Annals of DAAAM and Proceedings of the International DAAAM Symposium, C1-1

journal

Curved-layer fused deposition modelling

S Singamneni, O Diegel, B Huang, I Gibson, R Chowdhury

(2010), Vol. 8, pp. 95-107, Journal for new generation sciences, Bloemfontein, South Africa, C1-1

journal

Simulating dynamics of thoracolumbar spine derived from LifeMOD under haptic forces

K Huynh, I Gibson, W Lu, B Jagdish

(2010), Vol. 4, pp. 236-243, World academy of science, engineering and technology, Canakkale, Turkey, C1-1

journal
2009

Composite PLDLLA/TCP Scaffolds for Bone Engineering: Mechanical and In Vitro Evaluations

C Lam, R Olkowski, W Swieszkowski, K Tan, I Gibson, D Hutmacher

(2009), Vol. 23, pp. 1480-1483, IFMBE Proceedings, B1-1

chapter

Detailed spine modeling with LifeMOD?

S Tay, I Gibson, B Jagdish

(2009), i-CREATe 2009 - International Convention on Rehabilitation Engineering and Assistive Technology, E1-1

conference

Improving the mechanical properties in tissue engineered scaffolds

M Arafat, M Savalani, I Gibson

(2009), Vol. 2, pp. 3-6, ASME International Mechanical Engineering Congress and Exposition, Proceedings, E1-1

conference

Towards a Medium/High Load-Bearing Scaffold Fabrication System

I Gibson, M Savalani, C Lam, R Olkowski, A Ekaputra, K Tan, D Hutmacher

(2009), Vol. 14, pp. 13-19, Tsinghua Science and Technology, C1-1

journal

Composites in rapid prototyping

I Gibson, Y Liu, M Savalani, L Anand

(2009), Vol. 7, pp. 35-47, Journal for new generation sciences, Bloemfontein, South Africa, C1-1

journal
2008

The development of an artificial finger joint

I Gibson, S Chow, K Lam, W Lu, A Ngan, W Yip, K Chiu

(2008), pp. 157-190, Bio-materials and prototyping applications in medicine, New York, N. Y., B1-1

chapter

Finite element simulation of the spine with haptic interface

I Gibson, G Zhan

(2008), pp. 20-25, i-CREATe 2008 - International Convention on Rehabilitation Engineering and Assistive Technology 2008, E1-1

conference

Mechanical and in vitro evaluations of composite PLDLLA/TCP scaffolds for bone engineering

C Lam, R Olkowski, W ?wi?szkowski, K Tan, I Gibson, D Hutmacher

(2008), Vol. 3, pp. 193-197, Virtual and physical prototyping, Abingdon, England, C1-1

journal

A finite element simulator for spine orthopaedics with haptic interface

G Zhan, I Gibson

(2008), Vol. 3, pp. 141-149, Virtual and physical prototyping, Abingdon, England, C1-1

journal

Fusion behavior of TrueFormTM/SiO2 composite powders during selective laser sintering

K Fan, W Cheung, I Gibson

(2008), Vol. 14, pp. 87-94, Rapid Prototyping Journal, C1-1

journal
2007

Reflectance and transmittance of TrueForm? powder and its composites to CO? laser

K Fan, K Wong, W Cheung, I Gibson

(2007), Vol. 13, pp. 175-181, Rapid prototyping journal, Bingley, Eng., C1-1

journal

A 6-DOF haptic interface and its applications in CAD

Z Gao, I Gibson

(2007), Vol. 30, pp. 163-170, International journal of computer applications in technology, Olney, Eng., C1-1

journal
2006

Rapid prototyping: from product development to medicine and beyond

I Gibson

(2006), Vol. 1, pp. 31-42, Virtual and physical prototyping, Abingdon, Eng., C1-1

journal

Haptic sculpting of multi-resolution B-spline surfaces with shaped tools

Z Gao, I Gibson

(2006), Vol. 38, pp. 661-676, Computer-aided design, Amsterdam, The Netherlands, C1-1

journal

The use of rapid prototyping to assist medical applications

I Gibson, L Cheung, S Chow, W Cheung, S Beh, M Savalani, S Lee

(2006), Vol. 12, pp. 53-58, Rapid prototyping journal, Bingley, Eng., C1-1

journal

Rapid manufacture and GARPA

I Gibson, M Savalani

(2006), Vol. 12, pp. 1-2, Rapid prototyping journal, Bingley, Eng., C1-1

journal

Experimental investigation of ink on powder used for selective laser sintering

L Ming, I Gibson

(2006), Vol. 174, pp. 91-101, Journal of materials processing technology, Amsterdam, The Netherlands, C1-1

journal
2005

Haptic B-spline surface sculpting with a shaped tool of implicit surface

Z Gao, I Gibson

(2005), Vol. 2, pp. 263-272, Computer-Aided Design and Applications, Abingdon, Eng., C1-1

journal

Movement of powder bed material during the selective laser sintering of bisphenol-A polycarbonate

K Fan, W Cheung, I Gibson

(2005), Vol. 11, pp. 188-198, Rapid prototyping journal, Bingley, Eng., C1-1

journal

A novel artificial prosthetic replacement for the proximal interphalangeal joint of the hand - from concept to prototype

S Chow, K Lam, I Gibson, A Ngan, W Lu, W Ip, K Chiu

(2005), Vol. 10, pp. 159-168, Hand surgery, Singapore, C1-1

journal

Rapid prototyping: a tool for product development

I Gibson

(2005), Vol. 2, pp. 785-793, Computer-aided design and applications, Abingdon, Eng., C1-1

journal
2003

Constrained deformation of freeform surfaces using surface features for interactive design

J Zheng, K Chan, I Gibson

(2003), Vol. 22, pp. 54-67, International journal of advanced manufacturing technology, London, Eng., C1-1

journal

Morphology and properties of selective laser sintered bisphenol a polycarbonate

H Ho, W Cheung, I Gibson

(2003), Vol. 42, pp. 1850-1862, Industrial and engineering chemistry research, Washington, D.C., C1-1

journal
2002

Effects of graphite powder on the laser sintering behaviour of polycarbonate

H Ho, W Cheung, I Gibson

(2002), Vol. 8, pp. 233-242, Rapid prototyping journal, Bingley, Eng., C1-1

journal

Rapid prototyping for architectural models

I Gibson, T Kvan, L Ming

(2002), Vol. 8, pp. 91-99, Rapid prototyping journal, Bingley, Eng., C1-1

journal
2001

Desktop virtual reality interface for computer aided conceptual design using geometric techniques

J Zheng, K Chan, I Gibson

(2001), Vol. 12, pp. 309-329, Journal of engineering design, Abingdon, Eng., C1-1

journal

Colour RP

I Gibson, L Ming

(2001), Vol. 7, pp. 212-216, Rapid prototyping journal, Bingley, Eng., C1-1

journal
2000

Improving surface quality of selective laser sintered rapid prototype parts using robotic finishing

D Shi, I Gibson

(2000), Vol. 214, pp. 197-203, Proceedings of the Institution of Mechanical Engineers, part B: journal of engineering manufacture, London, Eng., C1-1

journal
1999

Effects of energy density on morphology and properties of selective laser sintered polycarbonate

H Ho, I Gibson, W Cheung

(1999), Vol. 89-90, pp. 204-210, Journal of Materials Processing Technology, Amsterdam, The Netherlands, C1-1

journal
1998

A new approach for direct manipulation of free-form curve

J Zheng, K Chan, I Gibson

(1998), Vol. 17, pp. 327-334, Computer graphics forum, Amsterdam, The Netherlands, C1-1

journal
1997

Material properties and fabrication parameters in selective laser sintering process

I Gibson, D Shi

(1997), Vol. 3, pp. 129-136, Rapid prototyping journal, Bingley, Eng., C1-1

journal
undefined

Development of a Detailed Human Spine Model with Haptic Interface

Kim Tho, Ian Gibson, Zhan Gao

(), Haptics Rendering and Applications, B1-1

chapter

Funded Projects at Deakin

Other Public Sector Funding

Development of fall arrest device

Prof Ian Gibson

  • 2016: $20,000

Industry and Other Funding

Development of fall arrest device

Prof Ian Gibson

  • 2015: $6,250

Active Baby: Dumbledoor

Prof Ian Gibson, Mr Angus Fitzpatrick

  • 2017: $17,500

Supervisions

Associate Supervisor
2017

Amirmahyar Khorasani

Thesis entitled: The Selected Laser Melting Production and Subsequent post-processing of Ti-6Al-4V Prosthetic Acetabular

Doctor of Philosophy (Engineering), School of Engineering